Wesman Ipsen Atmosphere And Vacuum Heat Treatment Furnaces

WESMAN IPSEN FURNACES

SEALED QUENCH FURNACES VACUUM

FURNACES TEMPERING FURNACES

With 20 years of experience and over 80 furnace installations, WESMAN IPSEN FURNACES is the Indian market leader for heat treatment equipment and solutions, with customers including the biggest names in the automobile, auto component, tooling, bearing, fastener and commercial heat treatment industries.

THE LEADER IN CONTROLLED ATMOSPHERE HEAT TREATMENT SOLUTIONS

Controlled atmosphere batch furnaces for heat treatment are manufactured by Wesman Ipsen Furnaces, a Wesman joint venture with Ipsen International GmbH, a world leader in heat treatment equipment and total heat treatment solutions. Wesman Ipsen atmosphere furnaces are designed to handle carburizing, carbo-nitriding, nitro-carburizing, hardening, tempering, normalizing and annealing.

CUSTOMER BASE

With 20 years of experience and over 80 furnace installations all over India, Wesman Ipsen is the market leader with a customer base including the biggest names in the automobile, auto component, tooling, bearing, fastener and commercial heat treatment industries. Customers include:

TVS Motor Co (two-wheeler components)

Hero Honda (two-wheeler components)

Bajaj Auto (two- and three-wheeler components)

Ashok Leyland (heavy vehicle components)

MICO (automotive components)

Yamaha Motors (two-wheeler components)

Lucas-TVS (automotive components)

NRB Bearings (bearings)

Rane TRW (automotive components)

Hindustan Motors (engine components)

TELCO (heavy vehicle components)

Sandvik Asia (cutting tools)

ADVANTAGES

Complete treatment cycle takes place in a protective atmosphere, preventing oxide formation during entire treatment. Treatment and transfer of load in furnace is fully automatic within the unit.

Pre-programmable temperature and carburizing curves for the complete heat treatment cycle

Rapid change from one treatment process to another

Optional cooling of the charge in oil or in circulated or static protective gas

Low protective gas consumption

Low outer furnace wall temperature

No lifting equipment needed for loading and unloading workbaskets

High output with low space requirement. No foundations are needed for erection, and units are delivered ready for service connections to be made

FURNACE MODELS

TQF SERIES CONTROLLED ATMOSPHERE SEALED QUENCH FURNACES

	Straight-through single chamber furnace with oil quench and forced atmosphere cooling
	Available in 16 standard sizes with operating temperature up to 1100°C
	Charge dimensions (W x L x H) from 280 x 460 x 300 mm to 1220 x 1820 x 910 mm
	Gross charge weight from 90 to 2000 kg

RTQPF SERIES CONTROLLED ATMOSPHERE SEALED QUENCH FURNACES

	In-out single chamber furnace with oil quench, purge vestibule and forced atmosphere cooling
	Available in 16 standard sizes with operating temperature up to 1100°C
	Charge dimensions (W x L x H) from 280 x 460 x 300 mm to 1220 x 1520 x 760 mm
	Gross charge weight from 90 to 1300 kg

DAC SERIES ATMOSPHERE TEMPERING FURNACES

	In-out single chamber furnace
	Available in 11 standard sizes with operating temperature up to 750°C
	Charge dimensions (W x L x H) from 380 x 610 x 300 mm to 1220 x 1520 x 760 mm
	Gross charge weight from 180 to 1300 kg

BT SERIES CONTROLLED ATMOSPHERE HARDENING FURNACES

	Straight-through single chamber furnace
	Available in 13 standard sizes with operating temperature up to 1100°C
	Charge dimensions (W x L x H) from 280 x 460 x 300 mm to 1220 x 1520 x 760 mm
	Gross charge weight from 90 to 1300 kg

ANCILLARY EQUIPMENT

WASHERS provide thorough cleaning of parts prior to and after heat treatment. Their design and dimensions are coordinated to match Wesman Ipsen’s automatic heat treating units, allowing them to be incorporated into an installation at any time. Available in spray and immersion models.
LOADERS allow safe and easy loading into the furnace chamber, with electromechanically driven pushbar to position the charge precisely and squarely in the furnace. A single roller unit can serve a complete group of furnaces. Available with either stationary or transversely driven conveyor roller track.

UNLOADERS unload the charge from the cooling chamber and transport it to the next process in the sequence. Power traversing versions reduce operator fatigue, increasing the operating efficiency of any installation.
ENDOGAS GENERATORS produce endothermic protective gas atmosphere or carrier gas for heat treatment. Available in capacities from 350 cfh to 6000 cfh in either gas-fired or electrically heated models.

VACUUM FURNACES

ANNEALING, SINTERING, BRAZING BRIGHT HARDENING, STRESS RELIEVING:
Horizontal chamber-type vacuum furnaces
Electrically heated, with low-pressure gas quenching up to 1.5 bars. Gross batch capacity 30 to 540 kg.
Pit-type vacuum furnaces
Electrically heated, with low-pressure gas quenching up to 1.5 bars. Gross batch capacity 25 to 1800 kg.

HARDENING, SOLUTION TREATMENT, SINTERING, BRIGHT ANNEALING, DEGASSING, BRAZING:
Horizontal chamber-type vacuum furnaces
Electrically heated with high pressure gas quenching up to 5 bars. Gross batch capacity 60 to 1000 kg